The CW-5 (CWO-1500 and CWE-1500) Circle Welder is designed for single pass or multipass welding of couplings or nozzles, using MIG or Flux cored wires, with or without gas shielding. The machine is equipped with its own wire feeder, welding control, drive motor, speed control for rotation, horizontal and vertical adjusting racks, rise and fall cam, gun and cable assembly, burnback control, 50 ft. (15 m) of control cable, and wire reel adaptor for 30 lb. (14 kg) spools. Welding control has wire feed speed (amperage control), cold wire inch, wire direction and weld switches.
|
||
 |
 |
 |
CWO-3670 The step adaptor is used from 1/2" to 4" (13 to 102 mm) on sprinkler pipe. |
CWO-3675 1 1/4" - 1 1/2" - 2" - 2 1/2" - 3", 4" (32-38-51-64-76, 102 mm) |
CWO-5790 A tapered centering device used to center the machine on nozzles. The range of the Cone Adaptor is 1-1/4" to 4" (32-102 mm) diameter. |
CWO-1645 Provides a pendulum-type motion to the gun for weave welding. The speed and stroke of oscillation are adjustable |
3-Jaw Expandable Chuck 3-jaw lathe chuck with adaptor plate. For use with CW-5AX, CW-7, and CW-11. |
| Model | Welding Diameter | Wire Size | Rotation Speeds | Rise and Fall Cam | Rating Amps | Standard Equipment |
|---|---|---|---|---|---|---|
| CW-5 | 1-12" (25-300 mm) | .035-1/16"" (.08-1.6 mm) | 3-130 ipm (75-3300 mm/min) | 0-5" (0-125 mm) | 300 amps 100% duty cycle | Burn back control, horizontal & vertical adjustment gun and cable. |
| CW-5AX | 1-12" (25-300 mm) | .035-3/32" (.08-2.4 mm) | 3-130 ipm (75-3300 mm/min) | 0-5" (0-125 mm) | 500 amps 100% duty cycle | Same as CW-5 plus: meter kit, torch angle adjuster, flux hopper, nozzle & cone. |
 |
 |
 |
| CWO-4530 Carriage may be used only with CW-5 Circle Welders. The carriage, which is mounted on a standard monorail, is used to move the welder along a length of pipe. | CWO-4540 Carriage is mounted on a standard monorail and is used with the CB-1P Air Plasma Machine. A winch holds the machine and prevents it from falling into the hole when the slug drops. This carriage may also be used with the CW-5 Circle Welders. | CWO-4550 Carriage may be used with either the CW-5 Circle Welder or the CB-1P Air Plasma Machine. The primary use is with machines on "bridge crane" type setups, to allow the operator to raise or lower the machine while reaching over a number of pieces of pipe. The carriage may also be used on standard monorails. |
| Carriage | CW-5 | CW-5A | CW-5AX | CB-1 | CB-1P | CB-1P |
|---|---|---|---|---|---|---|
| CWO-4530 | X | X | X | |||
| CWO-4540 | X | X | X | X | X | X |
| CWO-4550 | X | X | X | X | X | X |
[Top of Page] [CW-7 Circle Welder] [CW-11 Circle Welder] [Circle Burners-Oxy-Fuel] [Circle Burners-Plasma] [Saddle & Elbow Cutters] [General Information] [Cypress Main Page] [Bug-O Systems Main Page]
